Like the title says. I installed a GPU, everything posts and boots fine. The lights on the Ethernet port are lit up and will stay lit up indefinitely (I assume) if I leave it at the kernel select screen.
But as soon as I load a kernel, the lights go dark. It also is not shown as an active client on my gateway, so it’s not working at all.
I’ve tried lots of commands I’ve found to force it up. It looks to me like the NIC assigned to vmbr0 is correct. Etc. I just can’t get it to work.
If I remove the GPU, it immediately works again. NIC stays up after the kernel loads and I can access the web UI as normal.
rooteprox. *
root@prox:*# ip a
- 10: «LOOPBACK, UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 :: 1/128 scope host noprefixroute valid_lft forever preferred_lft forever - enpsso: ‹BROADCAST, MULTICAST> mtu 1500 qdisc noop state DOHN group default qlen 1000 link/ether a8:a1:59:be:f2:33 brd ff:ff:ff:ff:ff:ff
enp0s31f6: «NO-CARRIER, BROADCAST, MULTICAST, UP> mtu 1500 qdisc pfifo_fast master vmbro state DOWN group default qlen 1000 link/ether a8:a1:59:be:f2:32 brd ff:ff:ff:ff:ff:ff
vmbrO: ‹NO-CARRIER, BROADCAST, MULTICAST, UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000 link/ether a8:a1:59:be:f2:32 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.3/24 scope global vmbro valid_lft forever preferred_lft forever
root@prox: *# cat /etc/network/interfaces
auto lo
iface lo inet loopback
iface enp0s31f6 inet manual
auto vmbro
iface vmbro inet static
address 192.168.1.3/24
gateway 192.168.1.1
bridge-ports enp0s31f6
bridge-stp off bridge-fd o
iface enps0 inet manual
source /etc/network/interfaces.d/*
root@prox: ~# service network restart
Failed to restart network.service: Unit network.service not found.
I had a stock Debian install actually rename the device for my NIC when I changed GPUs. You should double-check if your NIC has the same entry in /dev with and without the GPU. After I changed the name in some config files the NIC worked fine with the GPU in, it could be easy as that.
I read through your screenshot. The ip command has enp3s0 and the config has enp2s0, I think this might be it.
Ohhh. In that last line. I wasn’t even looking at that, I assumed the block above that was setting up the primary NIC…
I’ll see if changing that interface name does it…
I changed my settings to name nic cards by mac address instead of the enumeration as I got sick of the name changing when I would add/remove pci devices.
How do you do this? Idk what to even google, exactly.
I am not at home, but what I did was change the 99-default.link file. I found this from the two pages below. https://wiki.debian.org/NetworkInterfaceNames#CUSTOM_SCHEMES_USING_.LINK_FILES https://wiki.debian.org/NetworkInterfaceNames
Basically, by doing this, your nic cards will be forcibly named using the mac address:
Afterwards, you will need to reboot and then update your network config file to use the correct names. I don't ever change the network config with the GUI in proxmox as it has wrecked it too many times. I will update this reply again later with some more information on what to do.
Sorry, didn't make it home until today and not sure if you get notifications on edits. You will need a monitor and keyboard hooked up to your server as you will not have ssh access until the network config is "fixed". I would do the below with the GPU removed, so you know 100% that your networking config is correct before mucking about further.
Step 1 - Create 99-default.link file
Add a
/etc/systemd/network/99-default.linkwith the below contents.Step 2 - Reboot and find new name of NIC that will be based on MAC
I forget if you have to reboot, but I am going to assume so. At this point, you can get the new name of your nic card and fix your network config.
ip linkshould list all of your nic devices, both real and virtual. Here is how mine looks like for reference, with the MAC obfuscated:Step 3 - Fix your network config and restart network manager
You will need to edit your
/etc/network/interfacesfile so the correct card is used./etc/network/interfaces, just in case you mess something up.sudo vim /etc/network/interfaces(or whatever text editor makes you happy) It will need to look something like below. I have to have DHCP turned on for mine, so your config likely uses static. Really all you need to do is change wherever it says enp yada yada to theenxAABBCCDDEEFFyou identified above.sudo systemctl restart networking.serviceStep 4 - Profit?
Hopefully at this point you have nework access again. Check the below, do some ping tests, and if it doesn't work, double check that you edited the interfaces file correctly.
sudo systemctl status networking.servicewill show you if anything went wrong and hopefully show that everything is working correctlyip -br addr showshould show that the interface is up now.At this point, if all is well, I would reboot anyways, just to make sure. If you add any GPUs, sata drives, other PCI device, disable/enable wifi/bt in the BIOS, or anything else that changes the PCI numbering, you don't have to worry about your NIC changing.
Will give this a go! thanks!