Ask Lemmy
A Fediverse community for open-ended, thought provoking questions
Please don't post about US Politics. If you need to do this, try [email protected]
Rules: (interactive)
1) Be nice and; have fun
Doxxing, trolling, sealioning, racism, and toxicity are not welcomed in AskLemmy. Remember what your mother said: if you can't say something nice, don't say anything at all. In addition, the site-wide Lemmy.world terms of service also apply here. Please familiarize yourself with them
2) All posts must end with a '?'
This is sort of like Jeopardy. Please phrase all post titles in the form of a proper question ending with ?
3) No spam
Please do not flood the community with nonsense. Actual suspected spammers will be banned on site. No astroturfing.
4) NSFW is okay, within reason
Just remember to tag posts with either a content warning or a [NSFW] tag. Overtly sexual posts are not allowed, please direct them to either [email protected] or [email protected].
NSFW comments should be restricted to posts tagged [NSFW].
5) This is not a support community.
It is not a place for 'how do I?', type questions.
If you have any questions regarding the site itself or would like to report a community, please direct them to Lemmy.world Support or email [email protected]. For other questions check our partnered communities list, or use the search function.
Reminder: The terms of service apply here too.
Partnered Communities:
Logo design credit goes to: tubbadu
view the rest of the comments
Soldering. Anyone who tells you it's easy is wrong. :P
Was soldering a mod board to a Sega Mega Drive, but ended up getting solder on the cpu's contacts and needed to get a second one. And it was a pain getting the wires to bind to the traces.
And yes, I probably was doing everything wrong.
Soldering is easy if you have the right tools. Those old school solder irons with the ceramic element dangling inside a metal tube suck balls. Get yourself a direct heat iron like the pinecil and some flux and it’s SOOOOO much easier.
I've had tools, teachers, and time.
I can't solder or braze to save my fucking life, but I'll weld circles around you with oxy, stick, mig, or tig.
Doesn't make a damn bit of sense to me
I felt the same the first time I tried but it honestly takes a few tries to start getting it right. The kind of iron and solder matter a lot; the older ceramic core ones suck and the JBC/pinecil type are much superior. Part of the problem with the ceramic type ones is they have one setting - full blast - and not good temperature control. With a pinecil/JBC you can set the temperature to 300C and expect to get 300C. Too hot and it will boil off the flux before you're done soldering and you just get crud.
In terms of solder, leaded rosin core solder is the best. Don't worry about the lead, as long as you wash your hands. Use a brass sponge type thing to clean the tip frequently to remove crud
For through holes, I'd say get some veroboard off eBay and a bunch of cheap resistors and just start plugging away until you get better. Process is basically - have tip with a bit of solder, poke to pad and pin, put solder into joint and hold 1-3 seconds until solder flows onto pad and pin, remove tip. Putting some flux on in advance helps remove the oxides before soldering
For surface mount (side pads/pins), there are kits with cheap/obsolete/trash components you can just plug away at without fear of messing anything up. Soldering smt is a bit annoying but doable by hand without much training. the process is basically: tin one pad, use tweezers to place part and reheat the solder until the part is in place, solder the rest of the pads, reheat first pad to relieve stress.
Even for large parts, I used to have trouble with unsteady hands. If you are doing smt you really need a microscope or magnifying glass for anything smaller than 0805 - really helps with the visual feedback loop for hand positioning. A microscope significantly improved my dexterity and hand steadiness